Magnets

A pack of 10 - 10mm dia x 5mm thick x 3.2mm c/sink N42 Neodymium Magnets. The NORTH pole is on the countersunk face and the SOUTH pole is on the opposite face. These Magnets are plated with 3 layers of protective coatings - Nickel + Copper + Nickel (Ni-Cu-Ni). These magnets will have approximately 4400 Gauss on each face. Each magnet can support a steel weight of up to 2kg vertically from the magnetic face when in flush contact with a mild steel surface of equal thickness to the magnet. Each magnet can also support up to 0.4kgs in a shear position before beginning to slide down a steel surface under the same conditions. These magnets can be fixed in place using M3 c/s Screw and have a maximum operating temperature of 80 degrees C. These magnets can be fixed in place using an M3... Less

A pack of 10 - 10mm dia x 5mm thick x 3.2mm c/sink N42 Neodymium Magnets. The SOUTH pole is on the countersunk face and the NORTH pole is on the opposite face. These Magnets are plated with 3 layers of protective coatings - Nickel + Copper + Nickel (Ni-Cu-Ni). These magnets will have approximately 4400 Gauss on each face. Each magnet can support a steel weight of up to 2kg vertically from the magnetic face when in flush contact with a mild steel surface of equal thickness to the magnet. Each magnet can also support up to 0.4kgs in a shear position before beginning to slide down a steel surface under the same conditions. These magnets can be fixed in place using M3 c/s Screw and have a maximum operating temperature of 80 degrees C. These magnets can be fixed in place using an M3... Less

EXTREME POWER WARNING! - These magnets are dangerous! If your fingers are trapped between two they will cut the skin. Please note that they should only be handled with great care. A pack of 1 - 25mm dia x 20mm thick with 6mm counterbored hole N52 Neodymium Magnet. The NORTH pole is on the counter bored face and the SOUTH pole is on the opposite face. These Magnets are plated with 3 layers of protective coatings - Nickel + Copper + Nickel (Ni-Cu-Ni). These magnets will have approximately 6250 Gauss on each face. Each magnet can support a steel weight of up to 26kg vertically from the magnetic face when in flush contact with a mild steel surface of equal thickness to the magnet. Each magnet can also support up to 5.2kgs in a shear position before beginning to slide down a steel surface... Less

EXTREME POWER WARNING! - These magnets are dangerous! If your fingers are trapped between two they will cut the skin. Please note that they should only be handled with great care. A pack of 1 - 25mm dia x 20mm thick x 6mm hole N42 Neodymium Magnet. The NORTH pole is on the counter bored face and the SOUTH pole is on the opposite face. These Magnets are plated with 3 layers of protective coatings - Nickel + Copper + Nickel (Ni-Cu-Ni). These magnets will have approximately 5300 Gauss on each face. Each magnet can support a steel weight of up to 20kg vertically from the magnetic face when in flush contact with a mild steel surface of equal thickness to the magnet. Each magnet can also support up to 4kgs in a shear position before beginning to slide down a steel surface under the same... Less

EXTREME POWER WARNING! - These magnets are dangerous! If your fingers are trapped between two they will cut the skin. Please note that they should only be handled with great care. A pack of 1 - 48mm dia x 11.5mm thick x 8mm c/bore N42 Neodymium Pot Magnet. The NORTH pole is on the centre of the front face and the SOUTH is on the outer edge around it (both poles are on the same face). These Magnets are plated with 3 layers of protective coatings - Nickel + Copper + Nickel (Ni-Cu-Ni). Each magnet can support a steel weight of up to 90kg vertically from the magnetic face when in flush contact with a mild steel surface of equal thickness to the magnet. Each magnet can also support up to 18kgs in a shear position before beginning to slide down a steel surface under the same conditions. These... Less

Wire-free 868 MHz For use on external doors and windows The Easy Fit Door and Window Contact is designed to be used in conjunction with any Yale Easy Fit Alarm kit.The contact is to be fitted to external doors and windows and will activate the alarm in the event that the door or window to which it is fitted is opened.

EXTREME POWER WARNING! - These magnets are dangerous! If your fingers are trapped between two they will cut the skin. Please note that they should only be handled with great care. A pack of 1 - 25mm dia x 20mm thick x 6mm hole N42 Neodymium Magnet. The SOUTH pole is on the counter bored face and the NORTH pole is on the opposite face. These Magnets are plated with 3 layers of protective coatings - Nickel + Copper + Nickel (Ni-Cu-Ni). These magnets will have approximately 5300 Gauss on each face. Each magnet can support a steel weight of up to 20kg vertically from the magnetic face when in flush contact with a mild steel surface of equal thickness to the magnet. Each magnet can also support up to 4kgs in a shear position before beginning to slide down a steel surface under the same... Less

EXTREME POWER WARNING! - These magnets are dangerous! If your fingers are trapped between two they will cut the skin. Please note that they should only be handled with great care. A pack of 1 - 60mm dia x 28mm thick N42 Neodymium Pot Magnet. The NORTH pole is on the centre of the front face and the SOUTH is on the outer edge around it (both poles are on the same face). These Magnets are plated with 3 layers of protective coatings - Nickel + Copper + Nickel (Ni-Cu-Ni). Each magnet can support a steel weight of up to 110kg vertically from the magnetic face when in flush contact with a mild steel surface of equal thickness to the magnet. Each magnet can also support up to 22kgs in a shear position before beginning to slide down a steel surface under the same conditions. These magnets can... Less

'L' & 'Z' Brackets: for conversion of Armlock® 260 series magnets to inward opening door applications, the 'L' & 'Z' bracket kit consists of a standard 'L' bracket and two separate fully-adjustable plates which form the 'Z' bracket.

A pack of 2 - 15mm dia x 7.5mm thick x 4.2mm c/sink N42 Neodymium Magnets. The SOUTH pole is on the countersunk face and the NORTH pole is on the opposite face. These Magnets are plated with 3 layers of protective coatings - Nickel + Copper + Nickel (Ni-Cu-Ni). These magnets will have approximately 5100 Gauss on each face. Each magnet can support a steel weight of up to 3.56kg vertically from the magnetic face when in flush contact with a mild steel surface of equal thickness to the magnet. Each magnet can also support up to 0.712kgs in a shear position before beginning to slide down a steel surface under the same conditions. These magnets can be fixed in place using M4 c/s Screw and have a maximum operating temperature of 80 degrees C. These magnets can be fixed in place using an M4... Less

Surface mounting reed switch and magnet in similar plastic mouldings The reed unit has 5 screws 3 for making security loops and 2 connected to the reed Reed makes contact when subjected to a magnetic field

A pack of 10 - 10mm dia x 5mm thick x 3.2mm c/sink N42 Neodymium Magnets. The SOUTH pole is on the countersunk face and the NORTH pole is on the opposite face. These Magnets are plated with 3 layers of protective coatings - Nickel + Copper + Nickel (Ni-Cu-Ni). These magnets will have approximately 4400 Gauss on each face. Each magnet can support a steel weight of up to 2kg vertically from the magnetic face when in flush contact with a mild steel surface of equal thickness to the magnet. Each magnet can also support up to 0.4kgs in a shear position before beginning to slide down a steel surface under the same conditions. These magnets can be fixed in place using M3 c/s Screw and have a maximum operating temperature of 80 degrees C. These magnets can be fixed in place using an M3... Less

A pack of 1 - 25mm dia x 16mm thick N42 Neodymium Clamping Magnet with M5 Hook from the back. The NORTH pole is on the centre of the front face and the SOUTH is on the outer edge around it (both poles are on the same face). These Magnets are plated with 3 layers of protective coatings - Nickel + Copper + Nickel (Ni-Cu-Ni). Each magnet can support a steel weight of up to 20kg vertically from the magnetic face when in flush contact with a mild steel surface of equal thickness to the magnet. Each magnet can also support up to 4kgs in a shear position before beginning to slide down a steel surface under the same conditions. These magnets can be fixed in place using a Clamping Magnet and have a maximum operating temperature of 80 degrees C. These magnets are 25mm dia x 32mm from the magnetic... Less

A pack of 1 - 32mm dia x 18mm thick N42 Neodymium Clamping Magnet with M4 Hook from the back. The NORTH pole is on the centre of the front face and the SOUTH is on the outer edge around it (both poles are on the same face). These Magnets are plated with 3 layers of protective coatings - Nickel + Copper + Nickel (Ni-Cu-Ni). Each magnet can support a steel weight of up to 34kg vertically from the magnetic face when in flush contact with a mild steel surface of equal thickness to the magnet. Each magnet can also support up to 6.8kgs in a shear position before beginning to slide down a steel surface under the same conditions. These magnets can be fixed in place using a Clamping Magnet and have a maximum operating temperature of 80 degrees C. These magnets are 32mm dia x 38mm from the... Less

A pack of 1 - 44mm dia x 75mm tall Brushed Chrome Effect Magnetic Door Stop supplied with fixing screws and plugs. The door stop is made to a high quality smooth chrome effect finish with a maximum operating temperature of 50 degrees C. These magnetic door stops make great solutions as door catches & holders. They can be wall, skirting or floor mounted and are suitable for marine and caravan applications.

A pack of 1 - 32mm dia x 18mm thick N42 Neodymium Pot Magnet. The NORTH pole is on the centre of the front face and the SOUTH is on the outer edge around it (both poles are on the same face). These Magnets are plated with 3 layers of protective coatings - Nickel + Copper + Nickel (Ni-Cu-Ni). Each magnet can support a steel weight of up to 34kg vertically from the magnetic face when in flush contact with a mild steel surface of equal thickness to the magnet. Each magnet can also support up to 6.8kgs in a shear position before beginning to slide down a steel surface under the same conditions. These magnets can be fixed in place using a M6 Machine Screw and have a maximum operating temperature of 80 degrees C. These magnets are 18mm tall from the magnetic face of the magnet to the top of... Less

A pack of 1 - 19mm dia x 8mm thick x M5 thread hole N42 Neodymium Pot Magnet. The NORTH pole is on the centre of the front face and the SOUTH is on the outer edge around it (both poles are on the same face). These Magnets are plated with 3 layers of protective coatings - Nickel + Copper + Nickel (Ni-Cu-Ni). Each magnet can support a steel weight of up to 7kg vertically from the magnetic face when in flush contact with a mild steel surface of equal thickness to the magnet. Each magnet can also support up to 1.4kgs in a shear position before beginning to slide down a steel surface under the same conditions. These magnets can be fixed in place using a M5 Screw and have a maximum operating temperature of 80 degrees C. These magnets have a threaded stud protruding from the back (non... Less

A pack of 1 - 20mm dia x 14mm thick N42 Neodymium Clamping Magnet with M4 Hook from the back. The NORTH pole is on the centre of the front face and the SOUTH is on the outer edge around it (both poles are on the same face). These Magnets are plated with 3 layers of protective coatings - Nickel + Copper + Nickel (Ni-Cu-Ni). Each magnet can support a steel weight of up to 11kg vertically from the magnetic face when in flush contact with a mild steel surface of equal thickness to the magnet. Each magnet can also support up to 2.2kgs in a shear position before beginning to slide down a steel surface under the same conditions. These magnets can be fixed in place using a Clamping Magnet and have a maximum operating temperature of 80 degrees C. These magnets are 20mm dia x 34mm from the... Less

29.5 Kg, Master Magnetics #07222, Round Base Magnet

A pack of 1 - 32mm dia x 8mm thick x 5mm c/sink N42 Neodymium Pot Magnet. The NORTH pole is on the centre of the front face and the SOUTH is on the outer edge around it (both poles are on the same face). These Magnets are plated with 3 layers of protective coatings - Nickel + Copper + Nickel (Ni-Cu-Ni). Each magnet can support a steel weight of up to 35kg vertically from the magnetic face when in flush contact with a mild steel surface of equal thickness to the magnet. Each magnet can also support up to 7kgs in a shear position before beginning to slide down a steel surface under the same conditions. These magnets can be fixed in place using a 5mm c/s Screw and have a maximum operating temperature of 80 degrees C. These magnets have a countersunk central hole on the front (magnetic)... Less

A pack of 10 - 10mm dia x 5mm thick x 3.2mm c/sink N42 Neodymium Magnets. The NORTH pole is on the countersunk face and the SOUTH pole is on the opposite face. These Magnets are plated with 3 layers of protective coatings - Nickel + Copper + Nickel (Ni-Cu-Ni). These magnets will have approximately 4400 Gauss on each face. Each magnet can support a steel weight of up to 2kg vertically from the magnetic face when in flush contact with a mild steel surface of equal thickness to the magnet. Each magnet can also support up to 0.4kgs in a shear position before beginning to slide down a steel surface under the same conditions. These magnets can be fixed in place using M3 c/s Screw and have a maximum operating temperature of 80 degrees C. These magnets can be fixed in place using an M3... Less

A pack of 4 - 16mm dia x 5mm thick x 3mm c/sink N42 Neodymium Pot Magnet. The NORTH pole is on the centre of the front face and the SOUTH is on the outer edge around it (both poles are on the same face). These Magnets are plated with 3 layers of protective coatings - Nickel + Copper + Nickel (Ni-Cu-Ni). Each magnet can support a steel weight of up to 5.5kg vertically from the magnetic face when in flush contact with a mild steel surface of equal thickness to the magnet. Each magnet can also support up to 1.1kgs in a shear position before beginning to slide down a steel surface under the same conditions. These magnets can be fixed in place using a 3mm c/s Screw and have a maximum operating temperature of 80 degrees C. These magnets have a countersunk central hole on the front (magnetic)... Less

A pack of 1 - 19mm dia x 8mm thick x M5 thread hole N42 Neodymium Rubber Coated Pot Magnet. The NORTH pole is on the centre of the front face and the SOUTH is on the outer edge around it (both poles are on the same face). These Magnets are plated with 3 layers of protective coatings - Nickel + Copper + Nickel (Ni-Cu-Ni). Each magnet can support a steel weight of up to 3.3kg vertically from the magnetic face when in flush contact with a mild steel surface of equal thickness to the magnet. Each magnet can also support up to 1.65kgs in a shear position before beginning to slide down a steel surface under the same conditions. These magnets can be fixed in place using a M5 Screw and have a maximum operating temperature of 80 degrees C. These magnets are encased in a silicone rubber 'jacket'... Less

A pack of 10 - 10mm dia x 2mm thick x 3mm c/sink N42 Neodymium Magnets. The NORTH pole is on the countersunk face and the SOUTH pole is on the opposite face. These Magnets are plated with 3 layers of protective coatings - Nickel + Copper + Nickel (Ni-Cu-Ni). These magnets will have approximately 3500 Gauss on each face. Each magnet can support a steel weight of up to 1.1kg vertically from the magnetic face when in flush contact with a mild steel surface of equal thickness to the magnet. Each magnet can also support up to 0.22kgs in a shear position before beginning to slide down a steel surface under the same conditions. These magnets can be fixed in place using M3 c/s Screw and have a maximum operating temperature of 80 degrees C.

A pack of 2 - 20mm dia x 4mm thick x 5.2mm c/sink N42 Neodymium Magnets. The SOUTH pole is on the countersunk face and the NORTH pole is on the opposite face. These Magnets are plated with 3 layers of protective coatings - Nickel + Copper + Nickel (Ni-Cu-Ni). These magnets will have approximately 3600 Gauss on each face. Each magnet can support a steel weight of up to 4.8kg vertically from the magnetic face when in flush contact with a mild steel surface of equal thickness to the magnet. Each magnet can also support up to 0.96kgs in a shear position before beginning to slide down a steel surface under the same conditions. These magnets can be fixed in place using M5 c/s Screw and have a maximum operating temperature of 80 degrees C. These magnets can be fixed in place using an M5... Less

A pack of 4 - 19mm dia x 8mm thick x M5 thread hole N42 Neodymium Pot Magnet. The NORTH pole is on the centre of the front face and the SOUTH is on the outer edge around it (both poles are on the same face). These Magnets are plated with 3 layers of protective coatings - Nickel + Copper + Nickel (Ni-Cu-Ni). Each magnet can support a steel weight of up to 7kg vertically from the magnetic face when in flush contact with a mild steel surface of equal thickness to the magnet. Each magnet can also support up to 1.4kgs in a shear position before beginning to slide down a steel surface under the same conditions. These magnets can be fixed in place using a M5 Screw and have a maximum operating temperature of 80 degrees C. These magnets have a threaded stud protruding from the back (non... Less

A pack of 2 - 20mm dia x 4mm thick x 5.2mm c/sink N42 Neodymium Magnets. The NORTH pole is on the countersunk face and the SOUTH pole is on the opposite face. These Magnets are plated with 3 layers of protective coatings - Nickel + Copper + Nickel (Ni-Cu-Ni). These magnets will have approximately 3600 Gauss on each face. Each magnet can support a steel weight of up to 4.8kg vertically from the magnetic face when in flush contact with a mild steel surface of equal thickness to the magnet. Each magnet can also support up to 0.96kgs in a shear position before beginning to slide down a steel surface under the same conditions. These magnets can be fixed in place using M5 c/s Screw and have a maximum operating temperature of 80 degrees C. These magnets can be fixed in place using an M5... Less

A pack of 1 - 44mm dia x 75mm tall Shiny Gold Effect Magnetic Door Stop supplied with fixing screws and plugs. The door stop is made to a high quality smooth chrome effect finish with a maximum operating temperature of 50 degrees C. These magnetic door stops make great solutions as door catches & holders. They can be wall, skirting or floor mounted and are suitable for marine and caravan applications.

A pack of 1 - 27mm dia x 6mm thick x 6.0mm c/sink N42 Neodymium Magnet. The NORTH pole is on the marked countersunk face and the SOUTH pole is on the opposite countersunk face. These Magnets are plated with 3 layers of protective coatings - Nickel + Copper + Nickel (Ni-Cu-Ni). These magnets will have approximately 3500 Gauss on each face. Each magnet can support a steel weight of up to 3.5kg vertically from the magnetic face when in flush contact with a mild steel surface of equal thickness to the magnet. Each magnet can also support up to 1.75kgs in a shear position before beginning to slide down a steel surface under the same conditions. These magnets can be fixed in place using M6 c/s Screw and have a maximum operating temperature of 80 degrees C. This magnet can be fixed in place... Less

A pack of 2 - 15mm dia x 7.5mm thick x 4.2mm c/sink N42 Neodymium Magnets. The NORTH pole is on the countersunk face and the SOUTH pole is on the opposite face. These Magnets are plated with 3 layers of protective coatings - Nickel + Copper + Nickel (Ni-Cu-Ni). These magnets will have approximately 5100 Gauss on each face. Each magnet can support a steel weight of up to 3.56kg vertically from the magnetic face when in flush contact with a mild steel surface of equal thickness to the magnet. Each magnet can also support up to 0.712kgs in a shear position before beginning to slide down a steel surface under the same conditions. These magnets can be fixed in place using M4 c/s Screw and have a maximum operating temperature of 80 degrees C. These magnets can be fixed in place using an M4... Less