RA Studfix V2 NM (Nursery School Model with lower screen height positions) A complete Floor to Wall Mounting System suitable for Flat Screens with a maximum recommended weight of 80kg and maximum VESA configuration of 800x600. Designed for use in Nursery and Primary School environments where a lower screen position is required. This Nursery Model allows the bottom of an average sized 65 inch screen to be positioned approximately 25cm from Floor Level. A complete installation solution designed to enable Flat Screens or Touch Screens to be fixed to a wooden stud partition wall or solid wall and direct the weight of the screen directly to the floor. Ideal for installations when the wall itself cannot support the weight of a heavy screen. Suitable for Smart, Clevertouch, Ctouch, Promethean ATP, Philips, Samsung, LG, Panasonic, BENQ, iTouch, Vividtouch, Hitachi, Iiyama, iBoard, Genee Screens and many more................ The system includes two upright supporting box section legs which are fixed to the existing upright wooden studs inside the wall with a Wall Mounting Plate and Floor Plate included in the kit. This creates a rigid, safe and strong fixed mounting frame for the Flat Screen Mount (included) to fix onto and position the screen at a selection of height settings. All fixings, bolts, coach screws and plastic caps are included for a very neat and tidy installation. The two Upright Supporting Legs are hollow box section design and allow all connection cables to and from the screen to be routed through them. Cable exit entry slots are positioned on the inner sides of each leg to enable surface mounted cable trunking to route cables away to a connection panel if required (not included). Maximum CENTRE POINT of screen from floor level is approximately 1060mm. Minimum CENTRE POINT of screen from floor level is approximately 760mm. The Wall Mounting Plate can be fixed to the wall in a LOWER or HIGHER position to avoid any dado rails or network trunking on the walls surface. In the LOWEST position the centre of the plate will be 650mm from floor level and in the HIGHEST position the plate will be 980mm from floor level. The Wall Mounting Plate itself is 120mm high and has four mounting slots 400mm apart. Upright supporting legs are 500mm apart (centre to centre). Finished in durable White or Black powder coat finish. An Optional Extra Media Shelf is available for this system (RA Studfix Shelf) which can be positioned under the screen at a selection of height settings.
AV Parts Master
VISION TECHCONNECT V2 MODULE SPEAKON Also known as NL 4, this is a versatile professional audio connector exclusively used for speaker cable.
AV Parts Master
NovoTouch OPS Module VKW30 Full featured detachable PC module designed exclusively for the NovoTouch collaborative and interactive flat panel displays FEATURES Full featured detachable PC module for seamless integration into the NovoTouch interactive flat panel display Powerful 8th generation Intel Core processor with integrated Intel UHD graphics chipset Supports fast SSD and DDR4 RAM in a variety of configurations (Varies by model) HDMI Out (4K 30Hz) for connection to secondary display Up to five (5) high speed USB ports (USB v2 (x2) (USB v3 (x2) (USB 3.1 Type C (x1) for connectivity to a variety of devices including but not limited keyboards, mice and flash drives Integrated RJ45 port for network monitoring and management solutions Reduces clutter promotes a cable free workplace Easy installation and maintenance Rugged steel chassis for extra strength and integrity Kensington security slot for prevention against theft or unapproved removal
AV Parts Master
NovoTouch OPS Module VKW30 Full featured detachable PC module designed exclusively for the NovoTouch collaborative and interactive flat panel displays FEATURES Full featured detachable PC module for seamless integration into the NovoTouch interactive flat panel display Powerful 8th generation Intel Core processor with integrated Intel UHD graphics chipset Supports fast SSD and DDR4 RAM in a variety of configurations (Varies by model) HDMI Out (4K 30Hz) for connection to secondary display Up to five (5) high speed USB ports (USB v2 (x2) (USB v3 (x2) (USB 3.1 Type C (x1) for connectivity to a variety of devices including but not limited keyboards, mice and flash drives Integrated RJ45 port for network monitoring and management solutions Reduces clutter promotes a cable free workplace Easy installation and maintenance Rugged steel chassis for extra strength and integrity Kensington security slot for prevention against theft or unapproved removal
AV Parts Master
RA4.3 PM This mount kit allows replacement of the Sanyo Short Throw Projector originally fitted to Promethean 2 Systems Version 2 Version 3, with most Short Throw Projectors with the same or a very similar lens ratio. Promethean 2 System Version 2 This system is identified by its RECTANGULAR projector mounting arm which is slightly off set to the left above the IWB. Our Retro Fit Mount kit for this system is the RA4.3 PM. Promethean 2 System Version 3 Almost identical in appearance to the version 2 but with a round tip on the end of the projector mounting arm. Our Retro Fit Mount kit for this system is the RA4.3 PM. Promethean 2 System Version 4 This mount system has a very flat projector mounting arm positioned over the centre of the IWB. Our Retro Fit Mount kit for this system is the RA4.3 PM. The Ball Socket Design meets perfectly with the mount on the existing Promethean System Mount, allowing image adjustment in every direction. THE PROMETHEAN 2 SYSTEM VERSION 2 VERSION 3 CAN BE IDENTIFIED BY ITS RECTANGLULAR BOOM ARM WHICH COMES STRAIGHT OUT ABOVE THE WHITEBOARD AND IS SLIGHTLY OFF SET FROM THE CENTRE POINT OF THE IMAGE. THIS BOOM ARM HAS A SILVER MOUNT ON ITS RIGHT HAND SIDE THAT THE PROJECTOR IS SUSPENDED FROM Please see image above for maximum span of fixing legs to cover projector mounting holes. An image of the Promethean 2 System Version 2 Version 3 System is shown above for your reference identification. We also offer a Retro Fit Mount for the Promethean 2 System Version 1 (RA4.3PM 100)
AV Parts Master
This optional extra Wall Support Kit is designed for use when the floor cannot be drilled to secrure the original Media Mate Riser Floor Plate to the floor, due to Under Floor Heating or other reasons, or if you want to fix the riser to the floor AND the wall. The kit comprises of a Wall Support Bracket which is to be fixed to a secure wall and then fits around the upper part of the lower section on the twin lifting legs also a deeper Floor Plate with no mounting holes or a standard Floor Plate with fixing holes. This means the weight of the screen is still directed down to the floor, but is also secured to the solid wall. The maximum distance available between the rear face of the lifting legs and the wall surface with this kit is 95mm to allow for any wall mounted trunking. The images above show what is included in the kit how it looks when fitted to the riser itself. This kit is only suitable for our Media Mate ECO Riser V2 and Media Mate PRO Riser products.
AV Parts Master
DVI D dual link digital video cables from Cables To Go deliver the high performance, high bandwidth interface needed for video displays of today while leaving flexibility for the products of tomorrow. The DVI D dual link configuration provides enough bandwidth for resolutions up to 2048x1536 and allows high speed digital transmission up to 9.9Gbps. These precision engineered cables are fully compliant with the DVI standard as defined by DDWG (Digital Display Working Group).
AV Parts Master
FOR THE PRO Get the non-stop comfort you need for all-day competitive play with the Razer BlackShark V2 HyperSpeed—an ultra-lightweight wireless headset for esports. Designed for maximum performance a
AV Parts Master